Aocoda RC F405 V4 Flight Controller
3,999.00 ৳
Only 1 left in stock
Aocoda RC F405 V4 Flight Controller OSD Baro and BalckBox for Racing Drone
Specifications
- MCU: STM32F405RGT6, 168MHz, 1MB Flash
- Board V3.0-ICM Version: IMU: ICM42688 (SPI1)
- Board V3.0-MPU Version: IMU: MPU6888 (SPI1)
- Gyro: ICM42688P(SPI1)
- Baro: SPL06-001(I2C1)
- OSD: AT7456E(SPI2)
- Blackbox: 16MB(SPI3)
- Motor Output: 8ch
- 5x Uarts (1,2,3,4,5)
- 10x PWM outputs(including “LED strip” pad)
- 1x I2C
- 3x ADC (VBAT, RSSI, CURR)
- 3x LEDs for FC Status (Blue, Red) and 3V indicator(Red)
- Built-in inverter for SBUS input
- USB Type-C
- Dual camera input and free switching
- Receiver: ELRS/CRSF/S.BUS/Frsky/Futabayfysky/TBs Crossfre/DSMX
- DJI FPV OSD is supported by any spare Uart
Power
- Vbat Input: 12.6~33.6V (3~8S LiPo)
- BEC: 5V/2.5A, 9V/2.5A(Max.2.7A)
- No built-in Current Sensor
- Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot
Physical
- Dimensions: 37mm*37mm
- Mounting Hole: M3 30.5mm*30.5mm
- Weight: 9.4g
FC Firmware
- BetaFlight: AOCODARCF405V3
- INAV: AOCODARCF405V3
- ArduPilot(ChiBiOS): AOCODARCF405V3
Including
- F405 V4 FC*1
- 8PIN SH1.0mm connection cable*1
- M3 *8 shock-absorbing ball *4
.jpg)
Related products
-
KK2.1.5 LCD Flight Control Board
4,499.00 ৳Add to cartKK2.1.5 LCD Flight Control Board (Red Switch) The kk 2.1.5 flight controller is next big evolution of the first generation KK flight controller boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than …
-
APM Pixhawk Power Module With XT60
599.00 ৳Add to cartAPM Pixhawk Power Module With XT60 and BEC Specifications: APM Pixhawk Power Module With XT60 is a simple way of providing your APM and pixhawk with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum …
-
Add to cartNodeMcu Lua ESP8266 Board with CP2102 SP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. Features: 1. Open-source 2. Interactive 3. Programmable …
-
OMNIBUS F4 V3S Plus Flight Controller
3,600.00 ৳Add to cartOMNIBUS F4 V3S Plus Flight Controller F4 V3S Plus Flight controller: Item name: F4 V3 PLUS Flight Controller Firmware: OMNIBUSF4SD Size: 36x36mm Mounting holes: 30.5×30.5mm STM32 F405 MCU Dshot support Drag and Drop OSD configured via Betaflight MPU: MPU6000 (Send at random) SBUS / PPM AND Spketrum DSMX ports MicroSD card blackbox Baro (BMP280) 5v3a …
-
SpeedyBee F405 V3 + 50A 4in1 Stack
8,499.00 ৳Read moreSpeedyBee F405 V3 + 50A 4in1 Stack Flight Controller MCU : STM32F405 IMU(Gyro) : BMI270 USB Port : Type-C Barometer : Built-in OSD Chip : AT7456E chip BLE Bluetooth : Yes, Supported DJI Air Port : 6-pin connector/ direct soldering. BetaFlight Cam Control : Yes(CC pad on the front side) Current Sensor Input : Supported …
-
HC-06 bluetooth module
370.00 ৳Add to cartThis is a bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. The HC-06 module is a slave only device. This means that it can connect to most phones and computers with bluetooth but it cannot connect to other slave only devices …
