Aocoda RC F405 V4 Flight Controller
3,999.00 ৳
Only 1 left in stock
Aocoda RC F405 V4 Flight Controller OSD Baro and BalckBox for Racing Drone
Specifications
- MCU: STM32F405RGT6, 168MHz, 1MB Flash
- Board V3.0-ICM Version: IMU: ICM42688 (SPI1)
- Board V3.0-MPU Version: IMU: MPU6888 (SPI1)
- Gyro: ICM42688P(SPI1)
- Baro: SPL06-001(I2C1)
- OSD: AT7456E(SPI2)
- Blackbox: 16MB(SPI3)
- Motor Output: 8ch
- 5x Uarts (1,2,3,4,5)
- 10x PWM outputs(including “LED strip” pad)
- 1x I2C
- 3x ADC (VBAT, RSSI, CURR)
- 3x LEDs for FC Status (Blue, Red) and 3V indicator(Red)
- Built-in inverter for SBUS input
- USB Type-C
- Dual camera input and free switching
- Receiver: ELRS/CRSF/S.BUS/Frsky/Futabayfysky/TBs Crossfre/DSMX
- DJI FPV OSD is supported by any spare Uart
Power
- Vbat Input: 12.6~33.6V (3~8S LiPo)
- BEC: 5V/2.5A, 9V/2.5A(Max.2.7A)
- No built-in Current Sensor
- Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot
Physical
- Dimensions: 37mm*37mm
- Mounting Hole: M3 30.5mm*30.5mm
- Weight: 9.4g
FC Firmware
- BetaFlight: AOCODARCF405V3
- INAV: AOCODARCF405V3
- ArduPilot(ChiBiOS): AOCODARCF405V3
Including
- F405 V4 FC*1
- 8PIN SH1.0mm connection cable*1
- M3 *8 shock-absorbing ball *4
.jpg)
Related products
-
HC-06 bluetooth module
370.00 ৳Add to cartThis is a bluetooth module for use with any microcontroller. It uses the UART protocol to make it easy to send and receive data wirelessly. The HC-06 module is a slave only device. This means that it can connect to most phones and computers with bluetooth but it cannot connect to other slave only devices …
-
Ublox NEO-M8N GPS Module
2,200.00 ৳Add to cartUblox NEO-M8N GPS Module Features: Built-in compass GPS module Main chip: Ublox-M8N – With fast satellite searching speed and high precision – Includes round plastic shell and GPS folding support Package size: 15 x 12 x 2cm Package weight: 57g Packing Content: 1 x NEO-M8N Flight Controller GPS Module with Shell
-
Pixhawk PX4 2.4.8 Flight Controller
11,999.00 ৳Add to cartPixhawk PX4 2.4.8 Flight Controller 32 Bit ARM for Multicopters Specification: The board integrates with PX4FMU+PX4IO Pixhawk is with new 32 bit chip and sensor technology Processor: 32 bit 2M flash memory STM32F427 Cortex M4, with hardware floating point processing unit Main frequency: 256K, 168MHZ RAM 32 bit STM32F103 backup co processor Sensor: L3GD20 3 …
-
APM Pixhawk Power Module With XT60
599.00 ৳Add to cartAPM Pixhawk Power Module With XT60 and BEC Specifications: APM Pixhawk Power Module With XT60 is a simple way of providing your APM and pixhawk with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The on-board switching regulator outputs 5.3V and a maximum …
-
ArduPilot APM 2.8 Flight Controller Combo
9,399.00 ৳ – 10,499.00 ৳Select optionsArduPilot APM 2.8 Flight Controller Combo Introduction: Eliminate V2.52 Version Old 1.0mm 6P SM06B GPS interface , changed to the DF13-4P compass external I2C interface, Place the DF13-5P GPS interface with external interfaces of the compass , more convenient to connections GPS with external compass. Replaced the V2.52 I2C interface to multi-purpose MUX interfaces, which …
-
SP Racing F3 Acro Flight Controller
2,800.00 ৳Add to cartSP Racing F3 Acro Flight Controller The SP Racing F3 Acro Flight Controller gives you all the features you want, whether you’re into FPV racing, acrobatic flying or drone photography. The hardware was designed by the lead developer of Cleanflight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the Cleanflight …
