Flame Sensor fire detection module
65.00 ৳
In stock
Flame Sensor fire detection module
Flame Detection Sensor Module is sensitive to the flame, but also can detect ordinary light. Usually used as a flame alarm. Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection point of about 60 degrees, particularly sensitive to the flame spectrum.
This Flame Sensor Module is used to detect fire/flame source or other light sources of the wave length in the range of 760nm – 1100 nm. It is based on the YG1006 sensor which is a high speed and high sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation. Sensor can be a great addition in a fire fighting robot, it can be used as a robot eyes to find the fire source. When the sensor detects flame the Signal LED will light up and the D0 pin goes LOW.
Features:
Extremely sensitive to wavelength between 760-1100nm
Power supply indicator lamp
Comparator output indicator lamp
AO, real-time thermistor voltage signal output
DO, high / low electric level signal output
Analog quantity output
Threshold rollover electric level output
Threshold adjusted by potentiometer
Detection Angle Range: About 60 degrees
Power Supply: 3.3-5.5 V DC
Specification:
Working Voltage: 3.3v – 5v
Detect Range: 60 degrees
On-board LM393 chip
Dimension: 3.2cm x 1.4cm
Package Includes:
1 x Flame Sensor For Fire Detection Module IR Infrared 4 Wire Flame Detection Sensor Module IR Flame Sensor Module Detector Smart Sense For Arduino
Related products
-
Dust Sensor
850.00 ৳Add to cartDust Sensor Dust Sensor, A simple Air Monitor Overview Sharp GP2Y1010AU0F onboard, detecting fine particle larger than 0.8μm in diameter, even like the cigarette smoke Low power consumption, analog voltage output, the output level is linear with dust density Embedded voltage boost circuit to support wide range of power supply Specifications Sensitivity : 0.5V/(100μg/m3) Measurement …
-
PIR Motion Sensor
99.00 ৳Add to cartPIR Motion Sensor PIR Motion Detector Module Features Settling time: 60 seconds Compact size (24 x 32 mm) Supply Voltage: DC3V-5V Current drain :< 50uA Voltage Output: High/Low level signal: 0-3.3V High sensitivity Delay time: 5s-18 minute(as customer requirement) Operation Temperature: -15oC -70 oC Infrared sensor: dual-element, low noise, high sensitivity Light sensor: CdS photocell …
-
Add to cart
LM2596 DC-DC Buck Step Down Converter Module with LCD voltmeter Features: 1. Input voltage range: 4-40 v (40 v to limit the highest voltage). 2. Output voltage range:1.25V – 37V (decompression mode, input output must be greater than 2 V above). 3. Output current: 2 A continuous output. 4. Output power: the maximum 15 w. …
LM2596 DC-DC Buck Step Down Converter Module with LCD voltmeterRead More
-
Add to cart
W1209 Digital Temperature Controller Switch Module Description: W1209 DC 12V Red LED Digital Heat Cool Thermostat Temperature Control Thermometer Thermo Controller Switch Module + NTC Sensor Specifications: Temperature range :-50-110 ° Dimensions: 48.5 * 40mm Temperature control mode: ON / OFF Resolution:When temperature is 0.1°, the resolution is -9.9~99.9, other temperature segment is 1° Control …
-
Fingerprint Scanner Sensor JM-101
1,100.00 ৳Add to cartFingerprint Scanner Sensor JM-101 The sensor is relatively easy to use with any TTL capable microcontroller or system. Although this is not the exact same sensor, it is compatible with the fantastic tutorial Adafruit has put together (just note that the pinout from the connector is different!). There is also free Windows-based software available – …
-
Flex Sensor 2.2″
1,400.00 ৳Add to cartFlex Sensor 2.2″ Inch Bend Flex Sensor For Robotic Hand Electronic Gloves Flex2.2 Flex Sensor Pressure Sensor Resistive Flex Sensor Robotic Arm Power Glove Measuring Bending DIY A flex sensor or bend sensor is a sensor that measures the amount of deflection or bending. Usually, the sensor is stuck to the surface, and the resistance of the sensor element is varied by bending the …
